The 8 most common wheel bearing maintenance issues

16 Jun.,2025

 

The 8 most common wheel bearing maintenance issues

Wheel bearings may not be the first item you think of when making your fleet’s maintenance checklist. There are bigger components—the engine, the tires, the safety system—that, just by their nature, demand more of your attention.

Beijing SKF supply professional and honest service.

But that does not mean that wheel bearings can be swept under the rug, as failures can lead to serious consequences, some even as severe as the truck’s wheel flying off while driving.

So, with that in mind, these are the eight most common potential wheel bearing issues, and how to spot them.

1. Bearing set too tight

Wheel bearings should be set between 1 and 5/s of an inch (0.001-in. to 0.005-in.), and ideally in the middle of those two numbers.

“If it’s tighter than one thousand,you’re running very close to preload,” explains Divjot Singh, Application Engineer at NTN. “Imagine the lubrication getting squished out below the rollers. If there’s no lubrication layer, there  will be metal on metal contact creating heat, which leads to flaking. 

“The way to tell that it’s a high preload is that you will see wear on the large side of the roller,” he continues. “So, the rollers are tapered—imagine if you were to take a cross section: The top would be smaller, the bottom would be larger. And the wear, if it’s more on the bottom on the large side, that’s how you can tell that it’s from a high preload setting.”

The indication of an improperly set bearing comes from a noise the driver will hear on the road.

After hearing this noise, Singh says what technicians will do is isolate which side of the truck, or which axle, it’s coming from.

“Once they narrow that down,” he continues, “then they will actually inspect that side and then take the wheel end apart.. That’s when you will see this actual flaking. But, without actually taking the bearing out, you cannot see or you cannot tell how much damage has already happened.”

2. Bearing set too loose

This, Singh says, is more common than the bearing being set too tight.

“Typically what happens is, over time, bearing setting will become loose because there’s wear and tear,” he explains. “And, if the initial setting was too loose to begin with, the more wear and tear happens, the looser it is going to get eventually. So, as you can imagine, if it’s too loose, there’s going to be a lot of excess play and vibration in the system. This could lead to a multitude of issues not limited to wheel wobble, seal leakage, ABS and braking problems. Eventually a too loose setting will cause flaking at the small end of the rollers/races leading to failure.  If damage is severe, it could even lead to the wheel coming off.”

The indications are similar in each case, Singh says, but you won’t know whether the bearing is too tight or too loose until the technician opens it up to have a look.

A loose bearing, specifically, is what can lead to the wheel coming off while the truck is being driven—thus, the consequences can be severe both from a road safety perspective and also from a fleet liability perspective.

The bearing being set too loose or too tight are the most common potential failures, but it’s worth quickly running through the others as well.

3. Bearing overload

Overloading isn’t common and tends to be specific to certain applications—in the garbage truck segment, for instance. Sometimes you’ll see flaking across the entire raceway—it’s not towards the left or to the right, so it’s not from an improper setting, but from overloading.

4. Misalignment

Misalignment occurs when the bearings are not seated properly. Improperly seated bearings will still function, but they will not have the full life of a typical bearing. That said, Singh says that this is not a common issue; however, it is possible.

If you are looking for more details, kindly visit Hub Bearing.

5. Contamination

If the bearing has collected a significant amount of dust before installation, it can stick to the rust preventative substance on the bearing and this could lead to contamination.

“While installing, we tell the techs to make sure everything is clean, keep the bearings and all the parts in the boxes until you’re ready to work on it,” Singh recommends.

6. Improper Lubrication

“Contamination could also come from faulty lubrication,” Singh continues. “So, if the lubrication is not clean or if they did not properly flush the old one out, it could be from that, too.”

7. Impact Loads

This is a potential issue that can happen during installation. It’s not very common, as Singh notes, but possible if technicians do not use the proper pressing tools.

8. Fretting Damage

Fretting corrosion has a rusty appearance and can occur when the race spins or creeps inside of the hub—but, Singh notes, this is not very common at all.

Maintenance frequency

The answer to avoiding these issues is a simple one: Make sure wheel bearings are part of your fleet’s regular maintenance schedule.

How frequently that happens, like all maintenance, depends on your application or schedule. Trucks in the refuse applications, for example, tend to need more frequent bearing replacements than their over-the-road counterparts, because of the wide variations in weights from the constant loading and unloading. 

There’s no specifically correct interval—but, for instance, when the brakes are being checked makes for a good time to check the wheel bearings as well since the necessary components are being removed anyway.

5 Steps to Optimize Your Wheel Bearings' Longevity and Performance

Whether you’re cruising down the highway or navigating rough terrain, your vehicle’s wheel bearings play a crucial role in ensuring smooth and efficient rotation. Understanding how to maximize their lifespan and enhance performance is essential for a safe and enjoyable driving experience. Here are five essential steps to help you achieve just that:

Wheel bearings are installed as per the manufacturer’s specifications using a calibrated torque wrench. This needs proper care.

  • Over-tightening can increase friction and stress on the bearings, leading to premature wear.
  • Under-tightening can cause excessive play and instability in the wheel assembly.

Follow the recommended torque values and sequence provided in the vehicle’s service manual to ensure proper installation.

Apart from the basic essentials like lubrication and installation, over time the performance of the bearings are dependent upon how they are used.

  • Overloading can lead to premature failure: Avoid overloading your vehicle beyond its recommended capacity, as this can put excessive strain on the wheel bearings and lead to premature failure.
  • Wheel misalignment will also lead to wear: Improper wheel alignment can cause uneven wear and loading on the wheel bearings, affecting their performance and lifespan. Regularly check and adjust wheel alignment as needed to ensure even tire wear and optimal bearing operation.

By following these five essential steps, you can maximize the lifespan of your wheel bearings and enhance their performance for a smoother and safer driving experience. Regular maintenance, proper greasing, correct torquing during installation, and avoiding overloading are key factors in ensuring the longevity and reliability of your vehicle’s wheel bearings. Stay vigilant for signs of wear and address any issues promptly to keep your vehicle running smoothly on the road ahead.

A worn wheel bearing can last anywhere from a few hundred miles to several thousand miles, depending on the extent of the wear and driving conditions. However, driving with a worn wheel bearing can be dangerous and may lead to further damage to the vehicle’s suspension and steering components.

Signs of a bad wheel bearing include unusual noises such as grinding, humming, or growling coming from the wheels, excessive play or looseness in the wheel assembly, and uneven tire wear. If you notice any of these symptoms, it’s essential to have your wheel bearings inspected and replaced by a qualified mechanic.

Contact us to discuss your requirements of Sliding Bearing. Our experienced sales team can help you identify the options that best suit your needs.